Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 42

Страница: 42 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

), and then pressing the

key (without entering a password) to display the

first parameter.

Peak Tracking

The

Peak Tracking

function is a software utility that periodically adjusts the

laser current to keep the absorption peak of the measured component at a

known location. There are three choices:

for no peak tracking,

for peak

tracking (default), and

to reset the peak to its factory default setting.

Selecting

will return the current analyzer midpoint to the factory default

midpoint, and then automatically revert the parameter value to its setting

before the reset was initiated. In most cases, the peak tracking should be set

for on.

Pipeline Pressure

The

Pipeline Pressure

parameter sets the pipeline pressure (in mbar) in the

current dew point calculation or, if enabled, displays the current pipeline

pressure input through the

AI Pressure Input

. Enter the required value.

Pressure Unit

The

Pressure Unit

parameter designates the display units for the measured

absolute pressure in the cell. There are four choices:

for millibar,

for Torr,

for kPa, and

for PSIA.

Operator Password

0:No p/w >0:p/w

Peak Tracking

0:Off 1:On 2:Rst

Pipeline Pressure

0.00000

Enter a value (mb)

Pressure Unit

0:mb1:Torr2:kPa3:psi

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды