Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 82

Страница: 82 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

•

Common Weight

: Ratio of the measured spectrum that did not

match a reference spectrum.

•

Concentration

: Current measured (live) analyte concentration

(process or validation) in selected engineering units.

•

Concentration (ppmv)

: Current measured (live) analyte

concentration (process or validation) in parts per million by volume

(ppmv).

•

Concentration Process

: Measured analyte concentration of last

process reading in selected engineering units.

•

Concentration Unit

: Designates the display units for the measured

concentration.

•

Conc Process ppmv

: Measured analyte concentration of last

process reading in parts per million by volume (ppmv).

•

Conversion Type

: Sets the type of relations (ideal or real gas) used

in the dew point calculation [

for ideal gas relations or

for real gas

relations (

calculated using Peng-Robinson EOS)].

•

Cross Shift

: The amount shift applied to match the measured

spectrum to the reference spectrum when using Cross Correlation.

•

Current 2F Flag

: Displays the current scrubber protection usage

level: 0 = standard protection (used for non-differential units), 1 =

mid protection, 2 = high protection, 3 = maximum protection (no

usage).

•

Current Midpoint

: Current midpoint that the analyzer is using,

including any peak tracking adjustments.

•

Custom Precision

: Sets the number of viewable digits to the right

of the decimal point.

•

Daily Validation

: Enables or disables the time of day autovalidation

feature.

•

DC Level

: Signal level at the high end of the current ramp.

•

Dew Point

: Measured analyte concentration of last process reading

as a moisture dew point.

•

Dew Point Method

: Sets the industry standard method with which

the dew point temperature is determined when

Calculate Dew

Point

is enabled.

•

DO Alarm Setup

: Bitwise value that sets the functionality of the

Assignable Alarm, as listed in Table 2–3 on page 2–22.

•

Dry DC Level

: Signal level at the high end of the current ramp from

the last scrubber cycle.

•

Dry Pressure (mb)

: Measured pressure (0.0 for non-differential

units) of the gas sample from the last scrubber cycle in millibar (mb).

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды