Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 53

Страница: 53 / 114

Operating the Analyzer

Operator’s Manual

–

Set the

Start Validation

parameter to

and then press the

key

followed by the

and the

key to allow the validation to start. Allow

the validation sequence to complete.

Press the

key followed by the

key (to enter

Mode 2

) and then

press the

key twice.

View the newly calculated RATA values, and if desired, set

Update

RATA

to accept the changes. Leave the setting at

to reject

the changes and start over.

Re-run steps 2 through 4.

Press the

key followed by the

key (to enter

Mode 9

) to verify

the validation results and confirm that new RATA values are

operating correctly.

Press the

key

followed by the

key (to enter

Mode 1

) to return

to Normal Mode.

Automatic single or dual validation

Either one or two standards can be used for automatic single or dual validation;

Validation 1 and/or Validation 2, which are automatically introduced and

controlled by the analyzer. The validation is automatically initiated based on the

hour of the day and is controlled by the

Val Start Time

Daily Validation

and

Val Interval

parameters. Validation can also be initiated remotely using the

Start Validation

parameter or the

Start Validation

digital input.

Configure the Operator Parameter section with the Operator

Password set to

and one parameter.

Configure

Update RATA

by setting Operator Parameter01 to

225

. Other parameters can be added, if desired.

Press the

key followed by the

key (to enter

Mode 9

) to verify

the validation results.

Press the

key followed by the

key (to enter

Mode 2

) and then

press the

key.

View the newly calculated RATA values, and if desired, set

Update

RATA

to accept the changes. Leave the setting at

to reject

the changes and start over.

Press the

key

followed by the

key (to enter

Mode 1

) to return

to Normal Mode.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды