Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 52

Страница: 52 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

Application examples

To set manual dual validation

Two standards are used in this example, Validation 1 and Validation 2, which

are manually introduced into the analyzer.

Mode 7

and

Mode 8

are used to

run these standards.

Configure the

Operator Parameter

section with the

Operator

Password

set to

and one parameter.

Configure Update RATA by setting

Operator Parameter01

“225”. Other parameters can be added, if desired.

Introduce Validation 1 and press

followed by the

key (to enter

Mode 7

) to allow Validation 1 to run for the desired amount of time.

Introduce Validation 2 and press

followed by the

key (to enter

Mode 8

) to allow validation to run for the desired amount of time.

Press the

key followed by the

key (to enter

Mode 2

) and then

the

key.

View the newly calculated RATA values, and if desired, set

Update

RATA

accept the changes. Leave the setting at

to reject the

changes and start over.

Re-run steps 2 and 3.

Press the

key followed by the

key (to enter

Mode 9

) to verify

the validation results and confirm that new RATA values are

operating correctly.

Press the

key

followed by the

key (to enter

Mode 1

) to return

to Normal Mode.

To set semi‐automatic single or dual validation

In this scenario, either one or two standards (Validation 1 and/or Validation 2)

are used, which are automatically introduced and controlled by the analyzer.

Typically, the validation is initiated locally by the user or while the user is

present by initiating the

Start Validation

parameter or the Start Validation

digital input.

Configure the Operator Parameter section with the

Operator

Password

set to

and two parameters.

Configure

Start Validation

by setting Operator Parameter01 to

Configure

Update RATA

by setting Operator Parameter02 to

225

. Other parameters can be added, if desired.

Press the

key

followed by the

key (to enter

Mode 2

) and then

press the

key.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды