Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 19

Страница: 19 / 114

Operating the Analyzer

Operator’s Manual

–

If you do make an error, press the

key followed by the TEST key, and then

the

key to return to the parameter and enter the correct value.

Modes Defined

Use the keypad to access the following modes by pressing the

key first

followed by a number (

) to activate a mode. The

following section explains each mode and the corresponding information that

displays on the LCD.

Mode 1: (Normal Mode)

Mode 1

continuously displays updated measurements. Press the

key

followed by the

key.

The measurements displayed are:

•

ANA

: Refers to the concentration in the sample cell in units of the

analyte/component selected in

Mode 2

•

: Pressure in the sample cell in units selected in

Mode 2

•

: Temperature in the sample cell in units selected in

Mode 2

Mode 2: (Set Parameter Mode)

Mode 2

enables user to view and change measurement parameters. Follow the

procedure under

“To change parameters in Mode 2”

on page 2-15 for

viewing and changing any of the parameters.

When the

key is pressed, measurement will be suspended until

a new mode is established. The only modes that produce

measurements are

Mode 1

Mode 6

Mode 7

Mode 8

ANA: 4.0256ppmv

P: 954.4mb T: 76.1F

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды