Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 34

Страница: 34 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

If the display units are correct but the conversion factor is not correct for the

application, a custom conversion factor can be defined using Modbus. To set a

custom conversion fact, first choose the correct display units (based on the

Concentration Unit

parameter), and then define the conversion factor for the

associated display units using Modbus. If the Modbus register is set to

, then

the default conversion factor is used. However, if it is set to a value greater than

0, then that value is used as the conversion factor. Refer to the following

Modbus parameters for more information:

•

ppmv ConvFactor 00

•

lb ConvFactor 01

•

% ConvFactor 02

•

mg ConvFactor 03

•

ppmw ConvFactor 04

•

ppbv ConvFactor 05

•

ppbw ConvFactor 06

•

grn ConvFactor 07

•

user ConvFactor 08

The default conversion factors are defined in Table 2–2 below. These

conversions are only intended as a starting point and are specific to our most

common applications. Furthermore, weight-based units are dependent on the

molecular weight of the background stream, and therefore the conversion

factor must be determined on a case-by-case basis.

If a correct concentration unit option for the display does not exist, then a

custom display unit and conversion can be created using Modbus. To set a

custom display unit, select option

for the

Concentration Unit

parameter.

Next define the ASCII display text and associated conversion factor using

Modbus.

Based on ISO 13443:1996 Natural Gas - Standard reference

conditions are 15

C, 101.325 kPa and Normal reference

conditions are 0

C, 101.325 kPa. Default conversion factors are

based on pipeline quality natural gas.

Table 2–2

Default conversion factors

ppmv

lb/MMcf

mg/Nm3 ppmw

ppbv

ppbw

grn/ccf

1.00

0.0473933 0.0001

1.46

1.40

1000.00 1400.00 0.0626285

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды