Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 98

Страница: 98 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

–

Start Character

: If Active Connect is set to

With Start

Character

, enter the start character in this field.

–

Modem Mode

: Indicates the on-screen response type when

in Modem Mode (if

Modem Mode

is enabled).

–

Show IP Address After Ring

: Indicates whether to display

the remote IP address upon connection. The default setting is

Yes

•

Endpoint Configuration

–

Local Port

: Enter the local port number.

–

Auto increment for active connect

: Select to auto-

increment the local port number for new outgoing

connections. The range of auto-incremented port numbers is

50,000

59,999

and loops back to the beginning when the

maximum is reached.

–

Remote Port

: Enter the remote port number.

–

Remote Host

: Enter the IP address of the remote device.

•

Common Options

–

Telnet Com Port Cntrl

: This field is available for

configuration only when

Active Connect

is set to

None

Select

Enable

to permit Telnet communication to the unit.

The

Telnet Com Port Cntrl

feature is used in conjunction

with the Com Port Redirector (CPR) utility. Refer to the CPR

online Help for details.

–

Terminal Name

: This field is available for configuration only

when Telnet Mode is set to

Enable

Use the terminal name for the Telnet terminal type. Enter

only one name. When this option is enabled, the unit also

reacts to the end of record (EOR) and binary options, which

can be used for applications such as terminal emulation to

IBM hosts.

–

Connect Response

: A single character is transmitted to the

serial port when there is a change in connection state. The

default setting is

None

–

Use Hostlist

: If this option is set to

True

, the device server

scrolls through the host list until it connects to a device listed

in the host list table. Once it connects, the unit stops trying to

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды