Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 97

Страница: 97 / 114

Ethernet Communications

Operator’s Manual

–

Channel Connection

Use the following procedure to configure a channel’s settings.

To configure a channel’s TCP settings

From the

Home

window, click

Connection

from the menu bar. The

Connection Settings

window for the channel displays.

In the available fields, enter or modify the following information. As

highlighted in Figure 4–4 on page 4–4, the main field to modify is

the

Local Port

. The available fields include:

•

Connect Protocol

–

Protocol

: From the drop-down menu, select TCP.

•

Connect Mode: Passive Connection

–

Accept Incoming

: Select Yes to accept incoming

connections. The default is Yes.

–

Password Required

: Determines whether or not a password

is required for an incoming passive connection. This field is

not available when a password is set for Telnet mode.

–

Password

: If Password Required was set to Yes, enter the

password for passive connections.

•

Connect Mode: Active Connection

–

Active Connect

: Select

None

to disable

Active Connect

Otherwise, indicate the connection type from the drop-down

list:

•

With Any Character

: Attempts to connect when any

character is received from the serial port.

•

With Active Mdm Ctrl In

: Accepts external connection

requests only when the

modem_control_in

input is

asserted.

•

With Start Character

: Attempts to connect when it

receives a specific start character from the serial port. The

default start character is a carriage return.

•

Manual Connection

: Attempts to connect when directed

by a command string received from the serial port.

•

Auto Start

: Automatically connects to the remote IP

address and port after booting up.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды