Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 24

Страница: 24 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

•

is for Validation 1 or Validation 2.

•

equals ‘Pass’ or ‘Fail’ for the validation result.

•

1000.00ppmv

is the concentration of the last

validation result in the user’s selected engineering

units. If the value is from a

Mode 7

Mode 8

validation, then it is the average validation value for

the time period during which the

Mode 7

Mode

was run.

Mode Test: (Analog Input Test Mode)

Mode Test

is used to view a real-time reading of the 4-20 mA analog input

state, as well as its current raw and scaled values for test and calibration

purposes. In this mode, the analyzer functions normally, as in Mode 1, except

that the LCD (display) shows the 4-20 mA analog input signal instead of the

current concentration, temperature and pressure. Press the

key followed by

the

TEST

key.

Configuring the Analyzer at Start-Up

SpectraSensors analyzers are pre-programmed at the factory with most

parameters set to default values, which are suitable for most applications.

There are a few parameters that should be set by the end user. SpectraSensors

recommends checking all the parameters at start-up.

Parameter Setting/Checking procedure

After the analyzer has been installed and start up has been

completed, press

Mode 2

(

) from the analyzer keypad and enter

password

3142

Press the

key repeatedly to scroll through the parameters and

verify the settings.

TEST

4-20 mA input is ON

4095 or 68948 mb

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды