Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 103

Страница: 103 / 114

Troubleshooting

Operator’s Manual

–

Instrument Problems

If the instrument issue is not resolved through re-setting the Process Peak

Tracking, refer to Table A–1 below before contacting Service (refer to

“Service

Contact”

on page A-4).

Table A–1

Potential instrument problems and their solutions

Symptom

Response

Non-Operation (at start up)

Refer to the Hardware Manual.

Non-Operation (after start up)

Refer to

“Service Contact”

on page

A-4

Laser Power Low Alrm

Press

to capture diagnostic data

and send the file to SpectraSensors.

Refer to the Hardware Manual.

Pressure Low Alarm

Pressure High

Alarm

fault

Refer to the Hardware Manual.

Temp Low Alarm

Temp High Alarm

fault

Refer to the Hardware Manual.

Front panel display is not lit and no

characters appear

Refer to the Hardware Manual.

Strange characters appear on front panel

display

Refer to the Hardware Manual.

Pressing keys on front panel do not have

specified effect

Refer to the Hardware Manual.

System stuck in

Fit Delta Exceeds

Limit

restart for greater than 30 minutes

Refer to

“Service Contact”

on page

A-4

Not getting enough flow to the sample

cell

Refer to the Hardware Manual.

No reading on device connected to

current loop

Refer to the Hardware Manual.

Current loop is stuck at 4 mA or 20 mA

Check display for error message. If

alarm has been triggered, reset the

alarm.

Refer to the Hardware Manual.

Reading seems to always be high by a

fixed amount

Capture diagnostic data and send the

file to SpectraSensors (see

“To read

diagnostic data with

HyperTerminal”

on page 3-5).

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды