Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 96

Страница: 96 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

To assign an IP address manually

From the

Home

window, click

Network

from the menu bar. The

Network Settings

window displays.

Select

Use the following IP configuration

Enter the following, as necessary:

•

IP Address

: If DHCP is not used to assign IP addresses, enter it

manually in decimal-dot notation. The IP address must be set to

a unique value in the network.

•

Subnet Mask

: A subnet mask defines the number of bits taken

from the IP address that are assigned for the host part.

•

Default Gateway

: The gateway address, or router, allows

communication to other LAN segments The gateway address

should be the IP address of the router connected to the same LAN

segment as the unit. The gateway address must be within the

local network.

When finished, click the OK button.

From the

Home

window, click

Apply Settings

from the menu bar to

save settings and initiate a reboot.

Ethernet configuration

Specify the speed and direction of data transmission.

To specify how data will be transmitted

From the

Home

window, click

Network

from the menu bar. The

Network Settings

window displays.

Enter the following, as necessary:

•

Auto Negotiate

: With this option, the Ethernet port auto-

negotiates the speed and duplex with the hardware endpoint to

which it is connected. This is the default.

If this option is not selected, complete the fields that become

available:

–

Speed

: The speed of data transmission. The default is

100

Mbps

–

Duplex

: The direction of the data transmission. The default is

Full

When finished, click the

button.

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды