Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 74

Страница: 74 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

Press the

key repeatedly until the

Modbus Address

parameter is

displayed.

Enter the desired

Modbus Address

and press the

key to store the

value and cycle to the

Modbus Mode

parameter.

Enter the desired

Modbus Mode

and press the

key to store the

value and cycle to the

2 Way Com Port

parameter.

Enter the

2 Way Com Port

assignment and press the

key to store

the value.

Press the

key followed by the

key to return to

Mode 1

. The

analyzer is now ready to receive Modbus queries.

Addressing

The analyzer's Modbus slave node address can be in the range of 0-250 with a

default of 1. All analyzers will respond to an address of 0, so this address can

be used to interrogate a single unit when its address is unknown or to

determine its address.

See Table 3–1 on page 3–15 for register definitions for both Gould and Daniel

Modbus modes. Be aware that for Gould Modbus the table follows the

convention of identifying the register with an offset of 40001. Therefore, the

actual value transmitted in the starting register field of the command is the

listed register value minus 40001, e.g., register 47001 is addressed as 7000.

Modbus Address

Enter a value(1-250)

Modbus Mode

0:Off 1:GMR 2:DMR

2 Way Com Port

0:Off1:Cus2:Ser3:Eth

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды