Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 94

Страница: 94 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

Refer to

“Network Mode”

on page 4-5 to enter values for the

Network menu.

The

Channel 1 Connection

menu displays the Ethernet ports TCP

connection settings, including the connection port. Refer to Figure

4–4 below.

Refer to

“Channel Connection”

on page 4-7 to enter values for the

Channel 1 Connection menu.

When finished, save and apply the configuration changes by clicking

Apply Settings

under the menu options. This will save the settings

and reboot the Ethernet port. This function will take approximately

60 seconds.

In the “Channel 1 Serial Settings” menu, do not change the

following parameters: Protocol (RS232), Flow Control (None),

Baud Rate (230400), Data Bits (8), Parity (None), and Stop Bits

(1).

Clicking

on each page does not change the configuration on

the Ethernet port, but simply confirms which changes to use.

Selecting “Apply Changes” will make the changes permanent and

initiate a reboot.

All remaining parameters should be left at default values unless

the user is knowledgeable in configuring the Ethernet.

Figure 4–4

Connection window (Web Manager)

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды