Endress+Hauser SpectraSensors SS2000e Скачать руководство пользователя страница 20

Страница: 20 / 114

NS 5.14 Firmware

–

4900002262 rev. B 3-23-21

Mode 3: not used

Mode 4: (System Diagnostic parameters)

Mode 4

displays system diagnostic data. These values may be useful when

troubleshooting the system. Press the

key followed by the

key.

The diagnostic parameters displayed are:

•

Temp:

Shows the temperature in the measurement cell when normal

sample gas is flowing through it.

•

Pres:

Shows the pressure in the measurement cell when normal

sample gas is flowing through it.

•

DC:

Shows the magnitude of the DC laser power in the measurement

cell when normal sample gas is flowing through it. Acceptable values

are between 800 and 3300. A number below or above this range will

trigger a

Laser Power too Low

Laser Power too High

respectively (see

“Alarms”

on page 2-42) indicating that either the

optics need to be cleaned or there is an alignment problem.

•

Zero:

Shows the detector signal value when the laser is turned off.

It should be in the range of -50 to +50. Outside of this range, a

Laser

Zero Low Alarm

Laser Zero High Alarm

(see

“Alarms”

page 2-42) occurs.

•

Fit:

The measure of “goodness of fit” for the last measurement point.

•

Mid:

The laser current set point after adjustment by the peak-

tracking software.

Mode 5: (4-20 mA Test Mode)

Mode 5

is used to turn on the 4-20 mA current loop (at the current set with

the

4-20 mA Test

parameter) for test and calibration purposes. Press the

key followed by the

key.

While in this mode the analyzer suspends measurement until you

return to

Mode 1, Mode 6, Mode 7 or Mode 8

Temp: 50.6 C

Pres: 1103.2 mb

DC: 2672

Zero: 12

Fit: 0.98

Mid: 60.24

Содержание SpectraSensors SS2000e



















































































































Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды

Endress+Hauser SpectraSensors SS2000e, Руководство оператора

Результаты поиска

Содержание SpectraSensors SS2000e

Отзывы:

Похожие инструкции для SpectraSensors SS2000e

Бренды по названию

Популярные бренды