ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 59 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

59

Batt volt

Indication of battery voltage protection based on

Analog protection

:

Batt >V

,

Batt <V

,

Batt V del

.

EarthFaultCurr

Indication of Earth fault current protection based on

Gener protect

:

EarthFaultCurr

and

EthFltCurr del

.

Dongle incomp

Incompatible (usually missing) dongle indication.

Hint:

The incompatible dongle is indicated e.g. in the case that:
- power management is enabled (

Pwr management

:

Pwr management

<> DISABLED) and there is no

dongle detected that enables this feature
- load sharing function is enabled (

Process control

:

#SysLdCtrl PtM

= LDSHARING or (

Process control

:

#SysLdCtrl PtM

= BASE LOAD and logical binary output MCB STATUS = 0 at the same time and controller

is not alone on the CAN bus)) and there is no dongle detected that enables this feature.
Incompatible dongle is not indicated in case of MINT operated in single island operation (no other controllers
detected on the CAN bus).

Emergency stop

Activity of Emergency stop (from Binary input Emergency stop) indication.

Hint:

Any Binary output alarm indication that follows the corresponding internal state is activated with alarm and
stays active until alarm reason disappears and the Fault reset (panel button or remote) is activated.

WrnSe2

The output closes when ServiceTime1 or ServiceTime2 has reached zero. To reset the output (and the
related WrnSeT2), it is necessary to set again a non-zero value to the corresponding setpoint.

WrnSe4

The output closes when ServiceTime3 or ServiceTime4 has reached zero. To reset the output (and the
related WrnSeT4), it is necessary to set again a non-zero value to the corresponding setpoint.

Overspeed

The output closes if the gen-set over speed alarm activates. The output opens, if alarm is no more active and

FAULT RESET has been pressed.

Underspeed

The output closes if the gen-set under speed alarm activates. Under speed limit is given by

Starting RPM

if

the engine has already started (see Starting procedure description). The output opens, if alarm is no more
active and FAULT RESET has been pressed.

Start fail

The output closes if the gen-set start-up fails (= Cranking issued

Crank attempts

times and engine did not

start). The output opens, if alarm is not active and FAULT RESET has been pressed.

Sd Stop fail

Engine stop fail indication. Stop fail: engine does not reach “still engine” condition within

Engine params

:

Stop time.

ChrgAlternFail

Charger fail detection. Guaranteed level for signal Charging OK = 80% of supply voltage.

Hint:

D+ output current is limited to cca 300 mA.

«
...
57
58
59
60
61
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: Faber Страницы: 8

Бренд: Wave Italy Страницы: 16

Бренд: TA Hydronics Страницы: 14

Бренд: Kärcher Страницы: 4

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 400

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 466

Бренд: Madison AV Страницы: 2

Бренд: Dahua Страницы: 137

UNDER CONTROL CP-30A PILOT

Бренд: G-Force Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды