ComAp IG-EE Скачать руководство пользователя

Страница: 82 / 117

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

Binary output IDLE/NOMINAL is opened before and during engine start (during

Idle time)

and after engine

start is activated - in Cooling state, only if

Engine params

Cooling Speed

= NOMINAL.

Step:

1 s

Range:

1 – 3600 s

Force value possibility: Yes

Hint:

The Under speed protection becomes active 5s after reaching

Starting RPM

or other engine running

condition regardless of the setting of

Idle time

(transition Idle -> Nominal RPM).

Min stab time

[ s ] (FV)

This is the minimum time the controller will wait, after switching the engine to nominal RPM, to close the
GCB (the delay ensures that the GCB is closed with correct generator frequency/voltage).
Step:

Range:

1 –

Max stab time

Force value possibility: Yes

Max stab time

[ s ] (FV)

This is the maximum time the controller will wait for generator voltage and frequency to build up, after
switching the engine to nominal RPM.
Step:

Range:

Min stab time

– 3600 s

Force value possibility: Yes

Hint:

When generator voltage in

Max stab time

does not reach defined limits (see

Gener protect

group), an alarm

occurs and the gen-set will cool down and stop.

Warming load

[ % ] (FV)

The requested load during warm-up period after GCB is closed. In parallel to mains operation only.
Step:

1 % of Nominal power

Range:

0 – 100 % of Nominal power

Force value possibility: Yes

Hint

Warming temp Analog input has to be configured. Otherwise the warm-up procedure does not work.

Warming temp [

C ] (FV)

The requested engine water temperature to finish the warming period. If this limit reached, the actual
Warming time is shorter than

Max warm time

setpoint.

Step:

Range:

± 32000

Force value possibility: Yes

Max warm time

[ s ] (FV)

If the required

Warming temp

is not achieved within this time, the warming period is completed anyway.

Step:

1 s

Range:

0 – 3600 s

Force value possibility: Yes

Cooling speed

[ NOMINAL / IDLE ]

(FV)

Determines function of

Idle/Nominal

binary output during cooling.

NOMINAL Gen-set cools down on nominal speed, generator voltage and frequency protections are active.
IDLE

Gen-set cools down on idle speed, generator protections are deactivated (except of Gen >V Sd).

Force value possibility: Yes

Cooling time

[ s ] (FV)

Runtime of the unloaded gen-set to cool down the engine before stop.
Step:

Range:

0 – 3600 s

Содержание IG-EE






















































































































Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды

ComAp IG-EE, Справочное руководство

Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды