ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 111 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

111

Force value possibility: Yes

Off load

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when an Off load type
protection occurs.
Force value possibility: Yes

Hint:

If enabled for an SMS type active call, an empty Alarmlist is sent, as this type of protection does not appear
there.

BrkOpen&CoolDn

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when a
BrkOpen&CoolDn type protection occurs.
Force value possibility: Yes

Mains protect

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when a Mains protect
type protection occurs.
Force value possibility: Yes

Hint:

If enabled for an SMS type active call, an empty Alarmlist is sent, as this type of protection does not appear
there.

Slow stop

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when a Slow stop type
protection occurs.
Force value possibility: Yes

Shutdown

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when a Shutdown type
protection occurs.
Force value possibility: Yes

AcallCH1..3-Type (FV)

Up to three separate channels are available for any of the following types of messages:

DISABLED:

Channel is disabled.

DATA-ANA:

Standard analog modem connection to monitoring SW.

DATA-GSM:

Standard GSM modem connection to monitoring SW.

DATA-ISDN:

Standard ISDN modem connection to monitoring SW.

DATA-CDMA:

CDMA modem connection to monitoring SW.

SMS-GSM:

Channel sends SMS message via GSM network. Only with GSM modem connected.

SMS-CDMA:

Channel sends SMS message via CDMA network. Only with CDMA modem connected.

IB-E-MAIL: Channel

sends

E-mail. Only when IG-IB connected.

IB-EML-SMS:

Channel sends E-mail in short format (SMS). Only when IG-IB connected.

Force value possibility: Yes

An Email contains

-

header with serial number and application info

-

Alarm list contents

-

latest 20 History records (reason, date, time)

Example of EML-SMS:

AL=(Sd Water Temp,Wrn Water Temp,!Emerg Stop,ActCallCH1Fail)

Hint:

GSM modem must be connected to controller for Active GSM call or SMS.
IG-IB does not support direct SMS, just as an email.
Connected device type (Analog / GSM / ISDN / CDMA modem) is recognized automatically.

«
...
109
110
111
112
113
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: U-Prox Страницы: 31

Бренд: Yardney Страницы: 8

Бренд: Fantech Страницы: 2

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: RAKwireless Страницы: 6

Бренд: UNISENSE Страницы: 16

Бренд: Xylem Страницы: 48

GA Industries 930-DT

Бренд: Vag Страницы: 4

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

Бренд: Tech 21 Страницы: 2

nERGY bluePRINT ENGCP15001

Бренд: Soundoff Signal Страницы: 5

Бренд: FMS Страницы: 9

Бренд: SIEB & MEYER Страницы: 119

TITAN-TRACKSIDE-6

Бренд: RC System Страницы: 4

Бренд: Samlex Solar Страницы: 3

Бренд: Dataq Страницы: 26

Бренд: Anritsu Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды