ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 44 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

44

IssueActCallC1

IssueActCallC2

IssueActCallC3

Rising edge on these binary inputs forces an active call to be issued via the corresponding channel.

Hint:

Can be used to send e.g. SMS in the case of a mains failure to report that the engine has successfully
started (linked from the output Gen params OK) and later on to report that the engine has stopped again
(linked from the inverted output Fuel solenoid).

ECUComFailBlck

The input blocks the issuing of the alarm in case of ECU communication failure.

Startblocking

The input blocks the engine start. If active, NotReady state is shown on the controller screen and a message
appears in the Alarmlist. As soon as input is deactivated, engine start is enabled again.

Hint:

Use this input for cooperation with external supervisory device, such as PLC. It can prevent the engine to be
started because of some reasons not known to the controller.

ECU StoppedEng

Engine stop was activated in ECU, not from controller. The controller reflects this situation and also goes to
Stop to avoid an Underspeed alarm (and record in the Alarm list).

CtrlHBeat sens

This input is used at a redundant controller to sense the "heart beat" from the main controller. The input is to
be connected to the output CtrlHeartBeat of the main controller.
If the redundant controller does not sense the heart beat from the main one, it will activate the binary output
CtrlHBeat FD, which has to be wired such a way, that it disconnects the dead main controller from the
genset, connects the redundant controller instead and activates it.

Force value 1 …16

If any of the particular 16 input s is active, the Force value function on that corresponding channel gets
active, forcing an alternative value to the selected setpoint.

CylDifEvalBlk

If the signal is active, the protection based on the difference amongst cylinder temperatures is blocked. After
signal deactivation, the protection is unblocked immediately.

CylDifEvalDel

Internal prot activity

CylDif evaluates deviation

BI: CylDifEvalBlk

CylDif Prot active

Fault reset

«
...
42
43
44
45
46
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Jeep Страницы: 32

Бренд: Accel Страницы: 8

Бренд: Campbell Страницы: 34

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Parkside Страницы: 86

disklavier DKC-850

Бренд: Yamaha Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды