ComAp IG-EE Скачать руководство пользователя

Страница: 36 / 117

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

Other CB fail reasons:

−

When the BO CB close/open is in steady state and CB feedback is changed, the CB fail is detected

immediately (no delay).

Alarm: GCB fail

BO GCB close/open

BI G CB feedback

Alarm detection:

immediatelly

active

closed

opened

Alarm: GCB fail

BI GCB feedback

BO GCB close/open

Alarm detection:

immediatelly

active

opened

closed

−

When the BO CB close/open opens, there is 5 resp. 2 sec delay for the breaker to respond before a CB

fail is detected. In such case, if CB OFF coil is used for opening the CB and CB fail occurs during
opening the CB, the signal CB OFF coil is automatically extended until the breaker opening is detected
(evaluated as CB status).

•

2 sec when the CB is used for synchronizing

•

5 sec in other cases

Alarm: GCB fail

BO GCB close/open

BI GCB feedback

active

opened

Time delay

5 sec

−

In case that CB fail is detected after switching the controller on (CB is closed), the CB OFF coil output is

activated immediatelly.

Содержание IG-EE






















































































































Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды

ComAp IG-EE, Справочное руководство

Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды