ComAp IG-EE Скачать руководство пользователя

Страница: 93 / 117

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

Gen V del

[ s ]

Delay for generator under and over voltage protection.
Step:

0,02 s

Range:

0,00 – 600,00 s

Gen >f

[ % ] (FV)

Threshold for generator over frequency in % of nominal frequency.
Step:

0,1

Range:

Gen<f

– 150,0 % of

Nominal freq

Protection:

BreakerOpen & Cool-down.

Gen <f

[ % ] (FV)

Threshold for generator under frequency in % of nominal frequency.
Step:

0,1

Range:

50,0 –

Gen>f

% of

Nominal freq

Protection:

BreakerOpen & Cool-down.

Hint:

The generator frequency is evaluated from the L3 phase.

Gen f del

[ s ]

Delay for generator under frequency and over frequency protection.
Step:

0,02 s

Range:

0,00 – 600,00 s

BusMeasError

[ DISABLED / ENABLED ] (FV)

DISABLED:

The protection is off.

ENABLED:

Bus measure error is detected in MINT / COX application when the voltage on controller‘s
bus terminals is out of limits 20 seconds after:

a)  GCB (own) was closed in MAN or AUT mode.
b)  MCB (feedback) was closed in AUT mode.
c)  Any other GCB in power management group (on CAN bus) was closed. The alarm is activated after

20 s, however the GCB (own) closing is blocked immediately from safety reasons.

Force value possibility: Yes
Protection:

BreakerOpen & Cool-down.

Reverse power

[ % ]

Threshold for generator reverse (back) power alarm in % of nominal power.
Step:

Range:

0 – 50 % of

Nomin power

Protection:

BreakerOpen & Cool-down.

ReversePwr del

[ s ]

Delay for generator back (reverse) power alarm.
Step:

0,1 s

Range:

0 – 600,0 s

Range:

-32000 – 0 kW

EarthFaultCurr

[ A ]

Threshold for generator Earth fault current protection. The value is measured via the 4

current terminal In /

Im3.
Step:

1 A

Range:

0 – 10000 A

Protection:

BreakerOpen & Cool-down.

EthFltCurr del

[ s ]

Delay for generator Earth fault current protection.

Содержание IG-EE






















































































































Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды

ComAp IG-EE, Справочное руководство

Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды