ComAp IG-EE Скачать руководство пользователя

Страница: 109 / 117

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

109

Step:

1 X

Range:

-32000 – 32000 X

Load shedding

Ld shed active

[DISABLED / ISLAND ONLY /

ISL+TRIP

PARAL

ALL

THE

TIME]

(FV)

DISABLED

Load shedding is switched off at all

ISLAND ONLY Load shedding is active only in island operation; before GCB closing all the LdShed

outputs get closed; in parallel operation with mains is always switched off

ISL+TRIP PARAL The same functionality as ISLAND ONLY, but in additional it closes all the LdShed outputs

during the power failure ( =change from parallel to island operation); according to the Load
in island operation it can be potentially reconnected beck

ALL THE TIME Load Shedding works only according to gen-set Power, it works without reference to

operation type (island, parallel or any transitions)

Force value possibility: Yes

Ld shed level

[ % ] (FV)

When gen-set load exceeds this level for more than

Ld shed delay

time, controller proceeds to the next Load

shedding stage - the next binary output Load shed x is closed.
Step:

1 % of

Nomin power

Range:

Ld recon level

- 200 % of

Nomin power

Force value possibility: Yes

Ld shed delay

[ s ] (FV)

Time delay for

LD shed level

limit.

Step:

0,1 s

Range:

0,0 – 600,0 s

Force value possibility: Yes

Ld recon level

[ % ] (FV)

When gen-set load drops under this level for more than

Ld recon delay

time, controller proceeds to the lower

Load shedding stage. The binary output for higher stage is opened (Load shed x). Automatic load
reconnection works only when

AutoLd recon

= ENABLED.

Step:

1 % of

Nomin power

Range:

0 -

Ld shed level

Force value possibility: Yes

Ld recon delay

[ s ] (FV)

The amount of time that the load has to be under

Ld recon level

before the next part of the load is

reconnected.
Step:

1 s

Range:

0 - 600 s

Force value possibility: Yes

AutoLd recon

[ DISABLED / ENABLED ]

(FV)

Switch between manual and automatic reconnection of shedded load.
DISABLED

Rising edge on binary input

MAN load recon

resets controller to the lower stage, but only if

the load is under the

Ld recon level

Ld recon delay

is not important in this case.

ENABLED

Load reconnection is automatic and depends on setpoints

Ld recon level

and

Ld recon

delay

. Binary input MAN load recon has no function.

Force value possibility: Yes

Hint:

To understand Load shedding better see diagrams in section Load shedding (page 10 and 11).

Содержание IG-EE






















































































































Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды

ComAp IG-EE, Справочное руководство

Результаты поиска

Содержание IG-EE

Отзывы:

Похожие инструкции для IG-EE

Бренды по названию

Популярные бренды