ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 70 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

70

Derating1 pwr

[ % ] (FV)

Derating2 pwr

[ % ] (FV)

The ratio of decreasing of the gen-set nominal power at

DeratingX end

level.

Step:

1 % of

Nomin power

Range:

0 - 100 % of

Nomin power

Hints:
DeratedX power

= 90% means the nominal power reduction

to

90%, not by 90%.

Derating ratio is set to zero and functions are not active when Analog inputs PowerDeratingX are not
configured (e.g. in default configuration).

When Power derating function is active, the generator nominal power is decreased to

DeratedX power

and

so Overload protection (BOC Overload) is based on this Derated power!

The generator nominal power is reduced according to the bigger restriction – the more reduced channel out
of the two.

Process control:
Derating1Start

[X]

Derating1End

[X]

Derated1Power

[%]

Power derating 1

analog input

Nominal power

influences Overload

protection etc.

Power derating

Process control:
Derating2Start

[X]

….

Power derating 2

analog input

Synchro enable

[ NONE / FORWARD ] (FV)

Enable or disable forward synchronization.
NONE: No synchronizing is enabled. Only closing GCB to dead bus allowed in this case.
FORWARD: GCB synchronizing is enabled.
Force value possibility: Yes

#Neutral cont.

[ EACH / COMMON ]

Setpoint changes behavior of binary output Neutral CB C/O that is used for Neutral contactor control.
EACH: Separate Neutral contactors and four pole GCB’s are supposed on each engine.

b) When GCB is opened (after start, before stop):

Binary output Neutral CB C/O (Neutral contactor) closes when Generator voltage is higher than 85%
of Nominal voltage.
Binary output Neutral CB C/O (Neutral contactor) opens when Generator voltage is lower than 50%
of Nominal voltage.

c) When more gen-sets are connected to the bus and MCB is opened (island running group) Binary

output Neutral CB C/O (Neutral contactor) is closed on running gen-set with the lowest

Contr.address

only. When lower controller address gen-set is connected to the bus, Neutral

contactor connection changes.

d) Binary output Neutral CB C/O (Neutral contactor) is opened when gen-sets are running in parallel to

the mains (MCB is closed).

«
...
68
69
70
71
72
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: Rain Bird Страницы: 48

Бренд: Mamas & Papas Страницы: 16

Бренд: Calsense Страницы: 74

Бренд: ZKTeco Страницы: 2

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Barcelona Страницы: 8

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 2

Бренд: J+J Страницы: 4

Бренд: Val Controls Страницы: 6

Hydropan-Single

Бренд: ETNA Страницы: 12

multisio 1D4-4RO ISO

Бренд: KBR Страницы: 8

Бренд: Applied Robotics Страницы: 13

Бренд: Daikin Страницы: 10

Бренд: GEM Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды