ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 52 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

52

RemoteControl1

RemoteControl2

RemoteControl3

RemoteControl4

RemoteControl5

RemoteControl6

RemoteControl7

RemoteControl8

These outputs are controlled remotely from InteliMonitor or other tool. The user selects the requested state
of these outputs via the buttons in this program.

Hint:

Outputs can be used to switch on/off some auxiliary devices in the control panel.

Binary outputs – Status information

Ready for load

The output closes when the engine is running, no 2

nd

level protection is active and the GCB is already closed

or is able to be closed (i.e. all generator parameters are within limits).

Gen-set active

The output closes together with Prestart output and opens together with achieving “still engine” condition
after the stop command. If the start sequence finishes with Start fail, the output opens after the last
unsuccessful start attempt.

Hint:

The output also closes if the engine begins to rotate spontaneously. It stays closed until “still engine”
condition is achieved.

Operational

The output is closed when no protection is active and the gen-set is ready for operation or is currently in
operation.

Ready

The output is closed, if following conditions are fulfilled:
- Gen-set is not running and
- No 2

nd

level protection is active (or not yet reset)

- The controller has no “engine running” indication from any source
- The controller is not in OFF mode

Not ready

The output is closed, if following conditions are fulfilled:
- The controller in OFF mode or
- Any 2

nd

level alarm is active or not yet reset

CrankProcedure

The output closes together with the first Starter activation and opens with the last Starter deactivation (either
“engine running” state achieved, or Start fail). During crank pauses, the output stays closed.

«
...
50
51
52
53
54
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: ABB Страницы: 2

Бренд: Quectel Страницы: 23

Бренд: Quectel Страницы: 79

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: BabySafe Страницы: 24

Бренд: jbc Страницы: 4

Бренд: jbc Страницы: 4

REVOLUTION Pro Controller 2

Бренд: Nacon Страницы: 11

Бренд: Nacon Страницы: 18

Бренд: Nacon Страницы: 24

Бренд: Nabco Страницы: 35

Бренд: Madison AV Страницы: 2

Бренд: EVERSPRING Страницы: 3

Бренд: elsner elektronik Страницы: 2

Бренд: Tool-Temp Страницы: 45

769N FireLock NXT Series

Бренд: Victaulic Страницы: 40

Бренд: Grundfos Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды