ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 110 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

110

PLC settings

The content depends on actual PLC configuration. Contains all setpoints related to the configurable PLC
blocks. If this setpoint group is empty, it is not displayed.

Timer channel 1-16

Defines the setting of particular timer channel.

There is 16 channels, each defines occurrence date and time (year, month, day, hour, minute), duration time
(in minutes, maximum is 24*60), repeating period (day, week, month, once). In case of week – day of the
week selection, when should be ex selection of repeating (every 1

st

, 2

nd

, 3

rd

or 4

th

week); In case of

month – day of the month selection (e.g. every 3

rd

day or every 2

nd

Monday)

Every channel can be disabled by blocking input. If blocking input is active then the timer is not activated
even if it should be, according to it’s other settings.
The channels are divided into groups of 4. Each group has independent binary output, which activates if any
of the 4 channels within the group is active (1-4, 5-8,...), see the picture below. There is also one common
output for all 16 channels.

Hint:

Timer channel 1-16 can be set via Pc software only. See Reference guide for GenConfig.

Act. calls/SMS

History record

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when a History record
type “protection” occurs.
Force value possibility: Yes

Hint:

If enabled for an SMS type active call, an empty Alarmlist is sent, as this type of protection does not appear
there.

Alarm only

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when an Alarm only
type protection occurs.
Force value possibility: Yes

Warning

[ DISABLED / ENABLED ]

(FV)

Enables or disables active calls/SMS/mails to selected phone, mobile or mail address when a Warning type
protection occurs.

«
...
108
109
110
111
112
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: S&C Страницы: 40

Бренд: Dantherm Страницы: 96

Бренд: Eaton Страницы: 6

Бренд: tams elektronik Страницы: 60

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Бренд: Rain Bird Страницы: 20

Бренд: Polycom Страницы: 2

Бренд: Baninni Страницы: 5

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: Gateway Страницы: 2

Бренд: CALEFFI Страницы: 6

Бренд: Oriental motor Страницы: 4

Бренд: Midland Страницы: 37

Бренд: XP Metal Detectors Страницы: 4

Бренд: Lumel Страницы: 32

Бренд: ZKTeco Страницы: 27

TITAN CONTROLS KRONUS 2

Бренд: Sunlight Supply Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды