ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 103 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

103

Sync/load control adjustment

Hint:

Use isochronous speed governor.
Two wire shielded connection from IGS-NT SPEED GOVERNOR output (SG OUT, SG COM) to Speed
governor auxiliary input is recommended.
A full range change of the IGS-NT speed governor output (from

SpeedGovLowLim

to

SpeedGovHiLim

)

should cause 5-10% change of the engine speed (

SpeedGovLowLim

~ 95% RPM

nom

,

Speed gov bias

~

100% RPM

nom

,

SpeedGovHiLim

~ 105% RPM

nom.

IMPORTANT

Speed governor has to be adjusted for optimum performance before Sync / load control adjusting.

Check generator phase sequence before the first GCB connection.

RPM

RPM

Volt [V]

Volt [V]

0 V

+10 V

- 10 V

Speed governor

voltage output

1500

0 V

- 10 V

1500

+10 V

Speed governor

voltage output

+ 5 % of nominal

+ 5 % of nominal

- 5 % of nominal

- 5 % of nominal

SpeedRegChar =

POSITIVE

SpeedRegChar =

NEGATIVE

Before optimal Sync/load setpoints adjusting disconnect GCB OPEN/CLOSE output or set

Phase window

=

0 to avoid paralleling.

Synchronizer adjustment

1) Start the engine in MAN Mode.
2) Set the engine RPM by speed trim on speed governor or by

Speed gov bias

and

SpeedGovLowLim

and

SpeedGovHiLim

to Nominal frequency.

3) To start synchronizing press GCB ON/OFF button. GCB LED starts to flash to indicate synchronization.

To stop synchronization press again GCB ON/OFF .

Slip control adjusting:
4) Adjust

Freq gain

to unstable speed control and decrease value by 30 % to insure stable performance.

5) Adjust

Freq int

to stable (fast and smooth) slip control. Synchroscope movement on the controller

measure screen should slow down and stop (in any position, because Angle control is off).

Angle control adjusting:
6) Set

Angle gain

. Synchroscope on the controller measure screen should move slowly and stop in “up“

position. Set

Angle gain

to unstable value (synchroscope swings) and decrease value by 30 % to

insure stable performance.

Load control adjustment

Prior to Sync/Load control adjustment, the Volt/PF control has to be adjusted! Load control loop is active in
parallel to mains mode only (MCB feedback closed). Switch off other engines while adjusting.
1) Set

#

SysLdCtrl PtM

= Baseload, set

Baseload

value to 30 % of Nominal power of one gen-set.

2) Set

Load gain

to the same value as

Slip freq gain

. Set

Load int

to zero.

3) Start the gen-set in MAN Mode, press GCB ON/OFF button to synchronize and close gen-set to mains.
4) When GCB is closed, gen-set load slowly increases to

Base load

value. Check that gen-set power is

positive (CT polarity!).

«
...
101
102
103
104
105
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: Bang & Olufsen Страницы: 9

Бренд: Bang & Olufsen Страницы: 12

Бренд: Hach Страницы: 86

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

Бренд: eclisse Страницы: 40

Бренд: Quectel Страницы: 95

Бренд: ICAS Страницы: 51

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: IBP Страницы: 12

Бренд: Vaillant Страницы: 12

Бренд: Vizio Страницы: 65

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренд: DeLaval Страницы: 102

TRIO MPC-165 Series

Бренд: Sutter Instrument Страницы: 60

Бренд: Sielco Elettronica Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды