ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 58 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

58

ECU comm error

Output closes if there is an error in the communication with ECU. It doesn’t matter how the ECU is
connected – J1939 link or RS232 line.

PeriphCommErr

Output closes if there is an error in the communication with any peripheral unit (e.g. IS-AIN8, IGS-PTM, ...).

CtrlHBeat FD

This output is used at a redundant controller to disconnect the main controller from the gen-set, connect the
redundant one instead and activate it. The output is closed:
- If the input CtrlHBeat sens is configured onto any input terminal and the redundancy controller does not
sense the "heart beat" signal from the main controller at that terminal.
- If the redundant controller has not received two consequent messages from the main controller. The
address of the main controller for the particular redundant one is selected by the the setpoint Watched Contr

CAN2 bus empty

The output closes if the controller doesn’t “see” any other controllers on the CAN2 bus. The output activation
can be blocked by setpoint

Basic settings

:CAN2empt

Detect

(So it should be DISABLED for single

applications.)

Bus meas error

The output closes when bus measurement protection is activated according to description of

Gener

protect

:

BusMeasError

setpoint.

Binary outputs – Configurable prog. States

J1939

Indication of J1939 communication fail (configurable between Nop protection, Warning or Shutdown).

KWP2000

Indication of KWP2000 communication fail.

SHBinCfGErr

Shared Binary module configuration error – i.e. more than one source was configured (is on the CAN2 bus).

SHAinCfgErr

Shared Analog module configuration error – i.e. more than one source was configured (is on the CAN2 bus).

PLC State 1 .. 4

PLC state indication.

ECUDiagBlocked

Output is active if any ECU is configured and when

Basic setting

:

ECU diag

= DISABLED.

Hint:

No ECU alarms are displayed on the controller screen.

WrongConfig

Wrong controller configuration indication.

Reverse power

Output is active when reverse power protection is active. Based on

Gener protect

:

Reverse power

and

RevPower del.

«
...
56
57
58
59
60
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: Jabra Страницы: 4

Бренд: TCS Страницы: 16

Бренд: M-system Страницы: 10

Бренд: HEIDENHAIN Страницы: 257

Entelli-Switch 250

Бренд: GE Страницы: 32

Бренд: Grundfos Страницы: 80

Бренд: Maker Factory Страницы: 3

Бренд: Exhausto CDT Страницы: 16

Бренд: gefran Страницы: 2

Dynamic Boiler Controller

Бренд: Intiel Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды