ComAp IG-EE Скачать руководство пользователя | Manualshive

Страница: 112 / 117

background image

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

112

AcallCH1..3-Addr

Address for channel 1...3 active call. Each above message type has either a phone number or an e-mail
address associated to it.

For more details see PC software guide chapter IG-IB Internet communication.

Hint:

To receive active call run InteliMonitor – Type of connection = Active call. Active call window contains list of
received ANT files. Each list item contains

Gen-set name

, Date, Time, controller serial number.

NumberRings AA

[ ]

Number of rings prior to answering the modem connection from PC to controller.
Step:

1

Range:

1 – 30

Hint:
NumberRings AA

change is not accepted immedately but after controller is switched on or when modem is

connected to controller.

ActCallAttempt

[ 1 to 250 ]

When an active call is issued, this setpoint defines the number of attempts to deliver the message.
Step:

1

Range:

1 to 250

Hint:

Timeout for connection is 90 sec and after 120 sec controller starts the next attempt. During the time the
controller is trying to issue an active call, incoming calls are blocked.

Acall+SMS lang

[ 1 to 7 ]

The setpoint specifies in which language the SMS and e-mail messages are issued in case of active call.
Adjusted number corresponds to the order of a language as configured in GenConfig. If the selected number
is out of range of possible languages of the controller, the first language is selected as default.

Date/Time

Time stamp act

[ DISABLED / ENGINE RUNNING / ALWAYS ] (FV)

Defines the activity of time stamp function:
DISABLED No

periodic

records are made.

ENGINE RUNNING Records are made with period given by

Time stamp per

only if engine is running.

ALWAYS

Records are made with period given by Time stamp per regardless of the engine state.

Force value possibility: Yes

Time stamp per

Time interval for periodic history records.
Step:

1

min

Range:

1 - 240 min

#SummerTimeMd

[ DISABLED / WINTER / SUMMER,

WINTER-S,

SUMMER-S

]

DISABLED: Automatic switching between summer and wintertime is disabled.
WINTER (SUMMER) : Automatic switching between summer and wintertime is enabled and it is set to
winter (summer) season.
WINTER-S (SUMMER-S) : Modification for southern hemisphere.

Hint:

Summer time is changed according to the last Sunday in March and time change is executed at 2 a.m. and it
is set to 3 a.m. Winter time change is done in the last Sunday in the October and from 3 a.m. is exchanged
to 2 a.m..

«
...
110
111
112
113
114
...
»

Содержание IG-EE






















































































































Отзывы:

Нет отзывов

Похожие инструкции для IG-EE

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Saitek Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: UE Страницы: 4

Бренд: Echelon Страницы: 40

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренд: Samsung Страницы: 32

Бренд: UNITED Страницы: 8

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Garmin Страницы: 4

Бренд: Hama Страницы: 8

Бренд: GBD Страницы: 15

Бренд: Zodiac Страницы: 12

Бренд: National Instruments Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды