manualshive.com logo in svg

AVM B1 v3.0, Руководство пользователя, Страница: 99 / 111

Поделиться
Скачать
AVM B1 v3.0 Скачать руководство пользователя страница 99

Error messages in Windows 3.x

Controller B1 v3.0 – 16 Troubleshooting

99

Error message: 

“

Error in the configuration file. Incorrect B1

controller type.”

Possible cause

: Different types of controllers (ISDN-Control-

lers for the ISA and PCI buses) are combined in your system.
During the installation of the additional controller, the ISDN-
LOAD.CFG and SYSTEM.INI files were not changed correctly.

Remedy

: Note the instructions for installing additional con-

trollers in the section for the relevant operating system.
When adding an AVM ISDN-Controller for a different bus
type, the line 

Type=XX

 must be added in the ISDNLOAD.CFG

file (“B1at” for ISA controller, “B1pci” for PCI controller). This
change must also be made in the SYSTEM.INI file.

Error message: Interrupt <xx> not available”

Possible cause

: The AVM ISDN-Controller B1 v3.0 and anoth-

er hardware device (like a sound card) are set to the same in-
terrupt. 

Remedy

: Check which interrupts (IRQs) are available in your

system by using the MSD.EXE program in the Windows direc-
tory. Then start the “B1 Setup” program from the “AVM” pro-
gram group and define another interrupt for the ISDN-Con-
troller. Windows must be restarted for these settings to take
effect.

Error message: “Installation error. Internal error: ISDN driver
not loaded.”

Possible cause

: The driver file B1CBASE.386 has been moved

or deleted, or the SYSTEM.INI file no longer contains the cor-
responding entry. 

Remedy

: Run the installation program SETUP.EXE from the

original installation disk.

Error message: The diagnostics program 

“

B1 Test” does not

run in Windows. 

Possible cause

: The test program was started while the driv-

er software (CAPI) was loaded.

HB_B1V30.book  Seite 99  Mittwoch, 7. Februar 2001  3:19 15

Содержание B1 v3.0
















































































































Отзывы:

Нет отзывов