AVM B1 v3.0 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 111

AVM B1 v3.0 Скачать руководство пользователя страница 63

Installation in Novell NetWare

ISDN-Controller B1 v3.0 – 10 Installation in Novell NetWare

63

10 Installation in Novell

NetWare

The driver software for the AVM ISDN-Controller B1 v3.0 in
Novell NetWare can be installed in the Novell NetWare ver-
sions 5.x, 4.x and 3.x.

Two installation variants are supplied for Novell NetWare 4.x
and 5.x: Stand-Alone CAPI and CAPI Manager. If you would
like to use the Novell CAPI Manager, make sure that it is in-
stalled before installing the ISDN-Controller B1 v3.0.

For Novell NetWare 3.x, only the Stand-Alone CAPI driver is
available.

The Novell CAPI Manager is a part of the Novell NetWare 4.x
and 5.x operating systems, and is supplied by Novell.

The installation and deinstallation procedures are almost
identical for both driver types and for all three Novell Net-
Ware versions. Configuration and operation of the ISDN-Con-
troller B1 v3.0 is different depending on whether the Stand-
Alone CAPI or the CAPI Manager version is used.

10.1 Installing the Driver Software

Before beginning with the software installation, check that
the ISDN-Controller has been installed in the computer prop-
erly. Make sure that an I/O address available in the computer
is set on the ISDN-Controller (see the section “Setting the I/O
Address” on page 14).

Perform the following steps to install the driver software:

The following instructions describe installation in Novell
Netware 5.x. Minor deviations may arise for Novell NetWare
3.12 and 4.x.

HB_B1V30.book Seite 63 Mittwoch, 7. Februar 2001 3:19 15

«
...
61
62
63
64
65
...
»

Содержание B1 v3.0
















































































































Отзывы:

Нет отзывов