AVM B1 v3.0 Скачать руководство пользователя страница 104

Страница: 104 / 111

Error messages in Novell NetWare

104

Controller B1 v3.0 – 16 Troubleshooting

Remedy

: First end all applications that use the ISDN-Control-

ler. Then you can unload or uninstall it.

Error message: “Installation error, I/O address <xxx> not
available.”

Possible cause

: The I/O address selected during installation

of the ISDN-Controller is used by another hardware device
and is not available.

Remedy

: Establish which I/O addresses are available in your

system. Then adjust the position of the jumper on the ISDN-
Controller to match the selected I/O address and enter the
new I/O address in the “b1setup” program. This program is
started by entering

load b1setup

at the server console.

Error message:

“

Installation error, Interrupt <xx> not

available.”)

Possible cause

: The interrupt set for the AVM ISDN-Controller

B1 v3.0 during installation is not available.

Remedy

: Check which interrupts (IRQs) are available in your

system. Enter

load b1setup

at the server console and set

another interrupt. Then reload the ISDN-Controller.

HB_B1V30.book Seite 104 Mittwoch, 7. Februar 2001 3:19 15

Содержание B1 v3.0
















































































































Результаты поиска

Содержание B1 v3.0

Отзывы:

AVM B1 v3.0, Руководство пользователя, Страница: 104 / 111

Результаты поиска

Содержание B1 v3.0

Отзывы: