manualshive.com logo in svg

AVM B1 v3.0, Руководство пользователя, Страница: 103 / 111

Поделиться
Скачать
AVM B1 v3.0 Скачать руководство пользователя страница 103

Error messages in Novell NetWare

Controller B1 v3.0 – 16 Troubleshooting

103

Error message: “Installation error, Controller-xx with I/O
address <xxx> does not answer.” 

Possible cause

: The ISDN-Controller was not completely

loaded, or the hardware has been damaged. 

Remedy

: Repeat the complete ISDN-Controller installation

procedure. To test the hardware, you may install the ISDN-
Controller in DOS and then run the program “B1 Test”. In
case of a hardware defect, please contact your dealer or
AVM.

Error message: “Installation error, Controller-xx with I/O
address <xxx> not found.”

Possible cause

: The position of the jumper that sets the I/O

address on the ISDN-Controller does not correspond to the
entry in the “B1 Setup” program, the I/O address is used by
another hardware device (such as a network adapter), or the
hardware is not installed. 

Remedy:

 Check which I/O address is available in your com-

puter and set the jumper on the ISDN-Controller accordingly
(see the section “Setting the I/O Address” on page 14). Then
enter the new I/O address in the driver software by entering

load b1setup 

at  the  system  console.  Then  reload  the

ISDN-Controller.

Error message: 

“

Installation error, Interrupt <xx> cannot be

used.”

Possible cause

: The AVM ISDN-Controller B1 v3.0 and anoth-

er hardware device (like a sound card) are set to the same in-
terrupt. 

Remedy

: Check which interrupts (IRQs) are available in your

system by using the MSD.EXE program in the Windows direc-
tory. Enter 

load B1 Setup

 at the server console and set a

different interrupt. Then reload the ISDN-Controller.

Error message: 

“

... at least one application is registered.” 

Possible cause

: You attempted to unload or uninstall the

AVM ISDN-Controller B1 v3.0 while an application (such as a
file transfer or fax program) was still using it.

HB_B1V30.book  Seite 103  Mittwoch, 7. Februar 2001  3:19 15

Содержание B1 v3.0
















































































































Отзывы:

Нет отзывов