AVM B1 v3.0 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 111

AVM B1 v3.0 Скачать руководство пользователя страница 15

Installing the ISDN-Controller B1 v3.0 in the Computer

ISDN-Controller B1 v3.0 – 2 Installing the Hardware

15

The figure below illustrates how the jumpers are arranged on
the ISDN-Controller B1 v3.0, showing the various jumper po-
sitions and their corresponding I/O addresses. These data
are also listed as a label on the circuit board of the AVM IS-
DN-Controller B1 v3.0.

Jumper positions and corresponding I/O addresses

* The jumper position “Plug & Play” is not yet supported by
the AVM ISDN-Controller B1 v3.0’s driver software. Check the
AVM Data Call Center from time to time to see if new drivers
have become available.

If there is no jumper switched on the ISDN-Controller, the
ISDN-Controller is set to the default I/O address of 150.

2.3 Installing the ISDN-Controller B1 v3.0

in the Computer

The next step is to physically install the ISDN-Controller in
your computer. The ISDN-Controller can be inserted into
either an 8-bit or a 16-bit slot of the computer. If both slots
are available, we recommend using the 16-bit slot.

Proceed as follows to install the AVM ISDN-Controller B1 v3.0
in the computer:

1.

Make sure that the PC and all peripherals are switched
off. Unplug their power cords.

Controller B1 v3.0

Slot back plate

ISDN jack

Switched jumper
(default setting)

I/O address 340

I/O address 300

I/O address 250

I/O address 150

Plug & Play

*

HB_B1V30.book Seite 15 Mittwoch, 7. Februar 2001 3:19 15

«
...
13
14
15
16
17
...
»

Содержание B1 v3.0
















































































































Отзывы:

Нет отзывов