AVM B1 v3.0 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 111

AVM B1 v3.0 Скачать руководство пользователя страница 102

Error messages in Novell NetWare

102

Controller B1 v3.0 – 16 Troubleshooting

Error messages in Novell NetWare

Error message:

“

CAPI not loaded.”

Possible cause

: You tried to start an ISDN application with-

out loading the AVM ISDN-Controller B1 v3.0 first.

Remedy

: Load the Controller B1 v3.0 by entering

load

capi20

at the system console and then start your ISDN ap-

plication.

Error message: “Error in configuration file, no ISDN-
Controller defined.”

Possible cause

: During the AVM ISDN-Controller B1 v3.0 in-

stallation, the configuration file CAPI20.CFG is created. If you
later edit this file manually and corrupt the ISDN-Controller
definition(s) it contains, the error occurs.

Remedy

: Repeat the complete AVM ISDN-Controller B1 v3.0

installation.

Error messages:

“

Deinstallation error, wrong CAPI driver loaded.”

“

Installation error, wrong CAPI driver loaded.”

“

Installation error, ISDN-Controller-xx unknown keyword

<xx>.”

“

Installation error, ISDN-Controller-xx <xxxx> value too

long.”

“

Installation error, ISDN-Controller-xx <xxxx> illegal value.”

Possible cause

: You have replaced some files in the ISDN-

Controller driver installation directory (on obtaining updated
drivers from the AVM Data Call Center, for example). Older
files in the same directory cause version conflicts.

Remedy

: Always perform the full AVM ISDN-Controller

B1 v3.0 installation procedure; never replace individual files.

HB_B1V30.book Seite 102 Mittwoch, 7. Februar 2001 3:19 15

«
...
100
101
102
103
104
...
»

Содержание B1 v3.0
















































































































Отзывы:

Нет отзывов