AUMA ACV 01.2 Скачать руководство пользователя страница 167

Страница: 167 / 168

T
Targ.speed end pos.

Temp. ctrls norm. ‰

Temp. ctrl unit norm ‰

Temperature-time

139

Thermal by-pass

Thermal fault

146, 148

Time format

Time not set

145

Timer CLOSE

Timer OPEN

Time speed incr.

Tolerance CLOSE

Tolerance OPEN

Tolerance range

Torque

Torque by-pass [s]

Torque config. CLOSE

Torque config. OPEN

Torque fault CLOSE

Torque fault OPEN

Torque peak [%]

Torque-travel

136 , 137, 137, 138

Torque wrn CLOSE

146

Torque wrn OPEN

145

Travel diff. dx

111

Travel diff. dx (MWG)

111

Tripping time

114

Trip torque CLOSE

Trip torque OPEN

Type of seating

U
Unit

46 , 47, 47, 48

Units

46, 46, 46, 47, 47,

47, 48, 48

Update firmware

126

V
Version

128

Volt.level diff. potent.

130

W
Warnings

144

Warnings (Cfg)

Work. val. activ. (AIN)

Working values (AIN)

Wrn controls temp.

Wrn dead bands

Wrn event mark

Wrn Fieldbus config.

Wrn FOC

Wrn FO cable budget

Wrn FOC connection

Wrn heater

Wrn input AIN 1

Wrn input AIN 2

Wrn no reaction

Wrn op.mode run time

Wrn op.mode starts

Wrn range act.pos.

Wrn ref.actual position

149

Wrn res. data in use

149

Wrn setpoint position

145

Wrn Setpoint Source

147

Wrn sign.loss act.pos.

Wrn Tm mark

Wrn torque CLOSE

Wrn torque OPEN

Wrong oper. cmd

167

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Parameter index

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

AUMA ACV 01.2, Руководство пользователя, Страница: 167 / 168

Результаты поиска

Содержание ACV 01.2

Отзывы: