AUMA ACV 01.2 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 168

background image

Targ.speed end pos. M1905

Default values:

8

(rpm)

Setting range:

6 ... 240 rpm

(revolutions/minute)

The adjustable speed range is indicated on the actuator name plate.

8.2.

Speed profile

Properties

The <Speed profile> function is used to change the actuator speed to a new
predefined value once the pivot point is reached. This way, different speed value
settings of up to ten sections across the overall travel (separately for each direction
of operation OPEN/CLOSE, if required) can be made. Thus, a valve specific speed
profile can be defined across the travel.

The speed between two pivot points is linearly interpolated (straight line). The speed
before to an end position (OPEN/CLOSED) to the first/last pivot point and vice versa
is constant (linearly even) to the first/last pivot point speed. Speed reduction prior to
end positions (parameter ) is not active.

The speed profile for EMERGENCY operations can be deactivated as desired.

Application

This function is used for special applications to avoid pressure surges. Pressure
surges might occur e.g. in case of a quick change of flow speed e.g. when quickly
closing a gate valve.

Figure 35: Example of a speed profile

[1/min]

0 %

100 %

P1 P2 P3 P4 P5 P6 P7 P8 P9

Drehzahl

Stellweg

[P]

Pivot points (P1 – P9)

Information

The speed profile can also be used for modulating actuators with activated positioner.
Refer to <Positioner> chapter.

8.2.1.

Speed profile: activate

Required user level:

Specialist (4)

or higher.

Device configuration M0053

Application functions M0178

Activation M0212

Speed profile M2122

Default value:

Function not active

Setting values:

Function not active

<Speed profile> function deactivated.

53

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Application functions

«
...
51
52
53
54
55
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: Garmin Страницы: 12

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

TLX-7000-FLRAILKIT

Бренд: IDEAL Страницы: 10

Бренд: S&C Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды