AUMA ACV 01.2 Скачать руководство пользователя страница 44

Страница: 44 / 168

13. Select:

→

Edit →

back to step 9: Set end position CLOSED "once again"

→

Esc →

back to step 4; either set end position OPEN or exit the menu.

Set end position

CLOSED via stroke

CMD0010

Information: If the end position OPEN is to be set via stroke, the end position
CLOSED must be set first via limit switching. For this, refer to

page 39, Limit

switching: set

14. Display indicates:

Set end pos.CLOSED? Stroke Yes No

15. Press

Down ▼

➥

Now, the incremented values for end position OPEN can be set.

16. Use

Up ▲ Down ▼

to adapt the incremented value in compliance with the

table at the beginning of this chapter.

Do not enter 0 as incremented value. Otherwise both set values are at the same
valve position.

Confirm incremented

value

17. Press

Save

to confirm new end position.

➥

Display indicates:

End pos. OPEN set!

➥

The right LED is illuminated (standard version) and thus indicates that the end

position OPEN setting is complete.

18. Select:

→

Edit →

back to step 12: Set end position OPEN "once again"

→

Esc →

back to step 4; either set end position CLOSE or exit the menu.

Information

If an end position cannot be set: Check the type of control unit in actuator.

7.4.

Date and time

After commissioning, we recommend checking and setting date and time. Date and
time are required for the event report function.

In case of a mains failure, date and time are stored. This data will only have to be
checked after a longer downtime.

Display M0009

Date and time M0221

Information

●

The date format, e.g. day/month/year, can be changed via the parameter

Date

format M0310

●

The time format, e.g. 12/24h can be changed via the parameter

Time format

M0050

●

For Profibus DP-V2 control, data and time can be synchronised using the
fieldbus.

7.5.

Display formats

The indications on the display can be represented in different formats: Country-specific
spellings, for example, can be accounted for.

7.5.1.

Date format

The data can be represented in day/month/year or in year/month/day.

Display M0009

Date format M0310

Default value:

DD.MM.YYYY

Actuator controls

Basic settings for commissioning

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды