AUMA ACV 01.2 Скачать руководство пользователя страница 5

Страница: 5 / 168

8.13.3.

FO cable baud rate, check setting

8.14.

By-pass function

8.14.1.

By-pass function: activate

8.14.2.

By-pass application: configure

8.15.

Automatic deblocking

8.15.1.

Automatic deblocking function: activate

8.15.2.

Operation time for operation in opposite direction: set

8.15.3.

Number of deblocking attempts: set

8.15.4.

Tolerance range: set

8.16.

Heater system and heaters

8.16.1.

Heater system within the actuator controls

8.16.2.

Heater on control unit (actuator)

8.16.3.

Motor heater

Failure functions....................................................................................................................

9.1.

Reversing prevention time

9.2.

Failure behaviour on loss of signal

9.2.1.

Failure reaction on loss of signal

9.2.2.

Failure source (failure reason) for a failure operation: set

9.2.3.

Failure operation (reaction of the actuator) on loss of signal

9.2.4.

Preset position: define

9.2.5.

Failure position MPV: define

9.2.6.

Speed for safety operation: set

9.2.7.

Delay time: set

9.3.

EMERGENCY behaviour

9.3.1.

EMERGENCY behaviour: activate

9.3.2.

EMERGENCY failure reaction

9.3.3.

Failure source (failure reason) for an EMERGENCY operation: set

9.3.4.

Operation mode for EMERGENCY behaviour

9.3.5.

EMERGENCY operation

9.3.6.

EMERGENCY position

9.3.7.

EMERGENCY speed

9.3.8.

Torque switching: by-pass

9.3.9.

Motor protection: by-pass

9.3.10.

Stepping mode: by-pass

9.3.11.

Operation profile: by-pass

9.3.12.

Interlock: by-pass

9.3.13.

Local stop: by-pass

9.3.14.

Speed profile: by-pass

9.3.15.

Delay time for EMERGENCY operation

9.4.

Enable local controls

9.4.1.

Enabling function: activate

9.4.2.

Enabling function behaviour

9.5.

Priority REMOTE

9.5.1.

Priority REMOTE: activate

9.5.2.

Priority REMOTE behaviour

9.5.3.

Fieldbus auto enable

9.6.

Interlock (enabling operation commands)

9.6.1.

Interlock: activate

9.6.2.

Source of Interlock enable signal: set

9.6.3.

Operation mode for interlock

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Table of contents

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды