AUMA ACV 01.2 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 168

background image

9.3.3.

Failure source (failure reason) for an EMERGENCY operation: set

Customer settings M0041

EMCY behaviour M0198

EMCY source M0591

Default value:

I/O interface

Setting values:

I/O interface

The EMERGENCY signal is present as binary signal (standard: +24 V DC) at a digital
input. If this voltage (i. e. the signal) is no longer present, the EMERGENCY behaviour
is initiated.

Fieldbus interface

The EMERGENCY signal is sent as fieldbus command. If the command is no longer
present, the EMERGENCY behaviour is initiated.

I/O or fieldbus

If the fieldbus command or the binary signal is no longer present, the EMERGENCY
behaviour is initiated.

Active interface

If active interface fails, the EMERGENCY behaviour is initiated; e.g. when changing
the command source the failure source for the EMERGENCY signal also fails.

9.3.4.

Operation mode for EMERGENCY behaviour

The EMERGENCY behaviour can be activated for the operation modes Remote
and/or Local

Customer settings M0041

EMCY behaviour M0198

EMCY operation mode M0202

Default value:

Remote only

Setting values:

Remote only

EMERGENCY behaviour is active in the operation modes:

Remote

,

Remote II

,

Fieldbus

Remote and local

EMERGENCY behaviour is active in the operation modes:

Remote

,

Remote II

,

Fieldbus

,

Local

,

Service

Information

In the operation mode Off (selector switch position 0), no emergency operation is
executed.

9.3.5.

EMERGENCY operation

The EMERGENCY operation determines which action is executed by the actuator
once the EMERGENCY behaviour is initiated.

Customer settings M0041

EMCY behaviour M0198

EMCY operation M0204

Default value:

STOP

Setting values:

STOP

The actuator stops in the current position.

CLOSE

The actuator runs to end position CLOSED.

OPEN

The actuator runs to end position OPEN.

Approach EMCY pos.

The actuator runs to the specified position.

9.3.6.

EMERGENCY position

If the

Approach EMCY pos.

EMERGENCY operation is set, the actuator runs to the

indicated EMERGENCY position.

Required user level:

Specialist (4)

or higher.

Customer settings M0041

89

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Failure functions

«
...
87
88
89
90
91
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

ACS850-04 series

Бренд: ABB Страницы: 296

Бренд: ABB Страницы: 320

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 56

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: J3C Страницы: 2

Бренд: Jäger Страницы: 50

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренд: saia-burgess Страницы: 203

Бренд: Sailor Страницы: 1

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: Xylem Страницы: 48

Бренд: Yealink Страницы: 6

MeetingSpace VC800

Бренд: Yealink Страницы: 6

Бренд: Yealink Страницы: 16

Бренд: Yealink Страницы: 299

VC210 Teams Edition

Бренд: Yealink Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды