AUMA ACV 01.2 Скачать руководство пользователя страница 72

Страница: 72 / 168

Customer settings M0041

Process controller M0742

Rate time Td M0746

Default value:

0 s

(seconds)

Setting range:

1 ... 100 s

8.7.11.

Actual value source (input for actual process value)

Customer settings M0041

Process controller M0742

Actual value source M0756

Default value:

I/O interface

Setting values:

I/O interface

The actual process value is defined via an analogue input (AIN 1 or AIN 2) of the
I/O interface.

Fieldbus interface

The actual process value is defined via the fieldbus.

8.7.12.

Speed source for actual process value

The actuator speed for control via the actual process value can be specified by
different sources.

Customer settings M0041

Process controller M0742

Speed source PID M1968

Default value:

Fieldbus

Setting values:

Fieldbus

The actuator speed is specified externally, via fieldbus. For this, four constant speed
values which may be programmed via fieldbus are available.

Internal 1

–

Internal 4

The actuator is controlled with a constant speed. For this, four programmable internal
speed values are available. The four internal speed values are programmed via
parameters

Speed internal1 M1930

–

Speed internal 4 M1933

2 DigIn: "Internal (1-4)"

External speed selection. For this setting, two external signals may be used to change
between the four internally programmed, constant speeds (

Internal 1

–

Internal 4

Two digital inputs have to be configured as control signals for speed selection.

Analogue input

The actuator speed is specified/modified externally via an analogue value (e.g. 0 –
20 mA). An analogue input has to be defined as speed source.

The speed range for the analogue input is determined via parameters

Speed rem.

min. M1936

and

Speed rem. max M1937

8.8.

Stepping mode

Conditions

This function requires one of the following equipments within the actuator:

●

Electronic control unit (non-intrusive version)

●

Potentiometer

●

Electronic position transmitter EWG/RWG

Characteristics

●

With stepping mode, the operating time can be increased for the entire or any
portion of the valve travel.

●

Stepping mode can be individually activated for the directions OPEN and
CLOSE.

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды