AUMA ACV 01.2 Скачать руководство пользователя страница 43

Страница: 43 / 168

Select parameter

Select parameter either:

→

click via the menu

to parameter, or

→

via direct display: Press and enter ID

M0084

➥

Display indicates:

Set end pos.CLOSED?

OPEN or CLOSED

Select via

Up ▲ Down ▼

→

▶ Set end pos.CLOSED? M0084

→

▶ Set end pos. OPEN? M0085

➥

The black triangle

▶

indicates the current selection.

Press

Information

If the end position CLOSED (or end position OPEN) is to be set via stroke, the end
position OPEN (or end position CLOSED) must be set first via limit switching. For
this, refer to

page 39, Limit switching: set

➥

The display indicates either:

Set end pos.CLOSED? CMD0009 →

continue with step 9

Set end pos. OPEN? CMD0010 →

continue with step 12

Specialist (4) →

continue with step 6

Log on user

Use

Up ▲ Down ▼

to select user:

Information: Required user level:

Specialist (4)

or higher

➥

The symbols have the following meaning:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

Press

to confirm selected user.

➥

Display indicates:

Password 0***

Enter password (

→

enter password).

➥

The display indicates either:

Set end pos.CLOSED? CMD0009 →

continue with step 9

Set end pos. OPEN? CMD0010 →

continue with step 12

Set end position

CLOSED via stroke

CMD0009

Information: If the end position CLOSED is to be set via stroke, the end position
OPEN must be set first via limit switching. For this, refer to

page 39, Limit

switching: set

Display indicates:

Set end pos.CLOSED? Stroke Yes No

10. Press

Down ▼

➥

Now, the incremented values for end position CLOSED can be set.

11. Use

Up ▲ Down ▼

to adapt the incremented value in compliance with the

table at the beginning of this chapter.

Do not enter 0 as incremented value. Otherwise both set values are at the same
valve position.

Confirm incremented

value

12. Press

Save

to confirm new end position.

➥

Display indicates:

End pos. CLOSED set!

➥

The left LED is illuminated (standard version) and thus indicates that the end

position CLOSED setting is complete.

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Basic settings for commissioning

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды