AUMA ACV 01.2 Скачать руководство пользователя страница 37

Страница: 37 / 168

Select main menu

Set selector switch to position 0 (OFF).

Press push button C

Setup

and hold it down for approx. 3 seconds.

➥

Display goes to main menu and indicates:

▶ Display

Select parameter

Select parameter either:

→

click via the menu

to parameter, or

→

via direct display: Press and enter ID

M0086

M0087

➥

Display indicates:

End position CLOSED

CLOSE or OPEN

Use

Up ▲ Down ▼

to select:

→

▶ End position CLOSED

→

▶ End position OPEN

➥

The black triangle

▶

indicates the current selection.

Press

➥

Display indicates the current setting:

Limit

Torque

➥

The bottom row of the display indicates either:

Edit →

continue with step 6

Save →

continue with step 10

Press

Edit

➥

Display indicates:

▶ Specialist (4)

User login

Use

Up ▲ Down ▼

to select user:

Information: Required user level:

Specialist (4)

or higher

➥

The symbols have the following meaning:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

Press

➥

Display indicates:

Password 0***

Enter password (

→

enter password).

➥

The screen indicates the pre-set type of seating (

▶Limit

▶Torque

) by means

of a black triangle

▶

Change settings

10. Use

Up ▲ Down ▼

to select new setting.

➥

The symbols have the following meaning:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

11. Confirm selection via

Save

➥

The setting for the type of seating is complete.

12. Back to step 4 (CLOSED or OPEN): Press

Esc

7.2.

Torque switching

Conditions

MWG in actuator (non-intrusive version).

For torque switches within the actuator (intrusive version), the torque switching is
set as described in the operation instructions pertaining to the actuator.

Function

●

Overload protection across full travel

●

Tripping in end positions (for torque seating)

●

Tripping in during manual operation also possible

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Basic settings for commissioning

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды