AUMA ACV 01.2 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 168

background image

Valve damage due to excessive torque!

→

Only apply torque by-pass with the consent of the valve manufacturer.

Torque by-pass: activate

Customer settings M0041

Torque switching M0013

Torque by-pass M0092

Default value:

Function not active

Setting values:

Function active

The torque by-pass is activated.

Function not active

The torque by-pass is deactivated.

Time interval for torque by-pass

During the time interval set here, the torque monitoring is deactivated.

Customer settings M0041

Torque switching M0013

Torque by-pass [s] M0205

Default value:

0.0 s

Setting range:

0.0 ... 10.0 s

seconds

Information

If torque by-pass is activated, the interval should be longer than the set time period
for reversing prevention time to ensure torque by-pass will also be effective in the
event of reversal of operation.

10.1.2.

Torque limitation of torque by-pass

For activated torque by-pass, the torque monitoring (parameter

Torque by-pass

M0092

) is deactivated for a defined (short) time. By activating the torque limitation,

torque monitoring will be activated again, but not in relation to the set tripping torque
but in relation to a torque peak which can be set separately via this function.

Condition

Electronic control unit with MWG in the actuator (non-intrusive version).

Activate torque limitation

Customer settings M0041

Torque switching M0013

Torque limitation M1805

Default value:

Function not active

Setting values:

Function active

The torque limitation of the torque by-pass is activated.

The actuator will be stopped during the by-pass interval and a torque fault will be
generated once the permitted torque peak has been exceeded.

Function not active

The torque limitation of the torque by-pass is deactivated.

There is no torque monitoring. During the by-pass interval, no torque fault will be
generated.

Set torque peak

Customer settings M0041

Torque switching M0013

Torque peak [%] M1806

Default value:

120 %

Setting range:

100 ... 150 %

(in relation to the set tripping torque)

106

Actuator controls

Monitoring functions

ACV 01.2/ACVExC 01.2 Profibus DP

«
...
104
105
106
107
108
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: Watts Страницы: 2

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды