manualshive.com logo in svg

AUMA ACV 01.2, Руководство пользователя, Страница: 134 / 168

Поделиться
Скачать
AUMA ACV 01.2 Скачать руководство пользователя страница 134

15.

Asset Management

The Asset Management function provides information (operational data, signals,
reports and characteristics), which can be used within an asset management system
but also generally for support during commissioning, maintenance or corrective
action.

15.1.

Operating data

Operating data provides details e.g. about the running time, the number of starts,
number of torque faults etc.

The analysis of this data provides valuable information regarding the optimization of
both actuator and valve. When using this information purposefully, actuator and valve
will be carefully operated, e.g. through appropriate parameter setting. In case of
faults, the logging of operating data allows for quick fault diagnostic.

View the operating data

Two counters are available, a lifetime counter and a resettable counter.

Asset Management M1231

Operational info M0177

Operational info total M0183
Operational info M0188

Description of the indications:

Operational info total

 = Lifetime counter

Operational info

 = Counter can be reset to 0

Table 21: Operating data

Description

Indication on display

Motor running time

Motor running time

Number of motor starts (starts)

Motor starts

Number of thermal faults (motor protection)

No. thermal faults

Number of torque faults in direction CLOSE

Torque fault CLOSE

Number of torque faults in direction OPEN

Torque fault OPEN

Number of limit switch trippings in direction CLOSE

Limit trip CLOSED

Number of limit switch trippings in direction OPEN

Limit trip OPEN

Number of torque switch trippings in direction CLOSE

Torque trip CLOSE

Number of torque switch trippings in direction OPEN

Torque trip OPEN

Total of all time intervals during which a start/run warn-
ing was signalled.

On time warning 1

Max. time interval during which a start/run warning was
signalled.

On time warning 2

Total of AUMATIC system starts

No. system starts

Maximum temperature of the controls

Max. temp. controls

Minimum temperature of the controls

Min. temp. controls

Maximum temperature of the MWG

Max. temp. MWG

Minimum temperature of the MWG

Min. temp. MWG

Operating hours counter: Number of hours during which
controls are supplied with power

Operating hours

Reset operating data

Required user level:

Specialist (4)

 or higher.

Asset Management M1231

Operational info M0177

Reset operation. info M0197

The entries in the operating data logging can be reset (deleted) via this menu.

134

 Actuator controls

Asset Management

 ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов