manualshive.com logo in svg

AUMA ACV 01.2, Руководство пользователя, Страница: 124 / 168

Поделиться
Скачать
AUMA ACV 01.2 Скачать руководство пользователя страница 124

13.

Service functions

The functions described here may only be changed by the AUMA service or by
authorised and trained personnel.

Menu item 

Service functions

 is only visible, if user level 

Specialist (4)

 or higher is

selected.

13.1.

Direction of rotation

Properties

This function allows changing the direction of rotation for actuator with 3-phase AC
motors.

The direction of rotation indicates the direction into which the drive shaft rotates
around its own axis. The view is on the top of the actuator. Distinction is made
between clockwise and counterclockwise rotation.

Information

●

When changing from clockwise closing to counterclockwise closing or vice
versa, only the direction of rotation of the motor is changed. The change-over
requires further action:
-

The wiring diagram designation is marked on the actuator controls name
plate. In case of a change, a new name plate with the new wiring diagram
number has to be requested from AUMA.

-

The wiring diagram number of the actuator is stored in the electronic device
ID (parameter 

Wiring diag. actuator M0060

). The ID has to be adapted to

the new designation once conversion is complete.

-

The actuator mounted to the actuator controls must be configured for the
set direction of rotation. Subsequent conversion from clockwise closing
to counterclockwise closing is possible using an AUMA conversion kit.

Parameters and instructions for setting

Setting the direction of rotation using parameters is only possible for actuators with
electronic control unit/MWG (Non-intrusive version).

Valve damage due to incorrect direction of rotation!

→

For 3-phase AC motors, the rotation direction of the actuator must match the
rotation direction of the valve.

Required user level:

AUMA (6)

.

Device configuration M0053

Actuator M0168

Closing rotation M0176

Default value:

Clockwise rotation

Setting values:

Clockwise rotation

The motor is controlled with a clockwise rotating field with the following sequence:
L1-U1, L2-U2, L3-U3 (clockwise closing).

Counterclockwise rot.

The motor is controlled with a counterclockwise rotating field with the following
sequence: L1-U3, L2-U2, L3-U1 (counterclockwise closing).

13.2.

Factory setting

The factory setting corresponds to the delivery state of the actuator controls.

When converting the controls e.g. by the AUMA service, a new factory setting can
be generated to adapt the modified configuration.

Former factory settings can be restored.

Generate new factory setting

Required user level:

Service (5)

 or higher.

124

 Actuator controls

Service functions

 ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов