AUMA ACV 01.2 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 168

background image

12.

Product variants

12.1.

Multiport valve

The multiport valve function is considered as product variant and must be activated
in the factory. Only for an activated multiport valve function will the respective
parameters be available for setting in the actuator controls menu.

Properties

The multiport valve function allows to directly access a valve port of a valve equipped
with several ports without stopping at any other port. Example: Operation from position
2 to 4 without stopping at position 3.

In operation modes Local and Fieldbus, up to 16 positions can be approached.
Operation mode Remote allows the function “next position” also up to 16 positions.

Depending on the setting, the actuator will either operate the valve at a defined
direction of rotation (counterclockwise or clockwise) or as quickly as possible
(irrespective of the actuator position) to the specified valve port.

Procedure for commissioning a multiport valve

1.

Set/check multiport valve parameters:
(generally, they are set in the factory prior to delivery)
-

Actuator type

-

Gear reduction ratio

-

Number of ports (positions)

-

Configuration of digital inputs

2.

Define/check positions (of valve ports).

3.

Set/check signal behaviour of positions.

4.

Set home port (zero position).

5.

Approach positions.

6.

If required, perform/correct multiport valve parameter settings like inertia, dead
band, backlash compensation and hysteresis.

7.

If further multiport valve parameters were set: Reset the homeport and re-set
parameters as required.

12.1.1.

Actuator type: set/check

The actuator type is set in the factory but can be modified at a later date.

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

Actuator type M1142

Default value: Actuator type set in the factory

Setting ranges: Selection list of all AUMA actuators

12.1.2.

Gear reduction ratio: set/check

The reduction ratio of the gear stage of the actuator mounted to the valve gearbox
must be set here. To facilitate adjustment, a selection table of supported gearboxes
is available.

Required user level:

Specialist (4)

or higher.

Customer settings M0041

Multiport valve M1140

Reduction ratio M1143

Default values:

GS50.3

117

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Product variants

«
...
115
116
117
118
119
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 40

Бренд: Hankscraft Runxin Страницы: 53

Бренд: 1Control Страницы: 8

Бренд: Jafar Страницы: 10

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренд: Omega Lift Страницы: 24

Бренд: Omega Lift Страницы: 8

Бренд: OMA Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды