AUMA ACV 01.2 Скачать руководство пользователя страница 4

Страница: 4 / 168

8.3.2.

Signal behaviour of intermediate positions: set

8.3.3.

Hysteresis for intermediate positions: set

8.4.

Operation profile (operation behaviour) for intermediate positions

8.4.1.

Operation profile: activate

8.4.2.

Operation profile for intermediate positions (pivot points): set

8.4.3.

Off times for intermediate positions (pivot points): set

8.5.

Two-wire control

8.6.

Positioner (operation mode Remote SETPOINT)

8.6.1.

Positioner: activate

8.6.2.

Adaptive behaviour: activate deactivate

8.6.3.

Overrun (inner dead band): set manually

8.6.4.

Max. error variable (outer dead band): set manually

8.6.5.

Dead time: set

8.6.6.

Hysteresis for positioner: set

8.6.7.

Closing fully/opening fully (end position tolerance for setpoint)

8.6.8.

Setting range: limit

8.6.9.

Speed reduction before reaching setpoint position

8.6.10.

Change-over between OPEN - CLOSE control and setpoint control

8.6.11.

Input of setpoint position

8.6.12.

Input range of setpoint position

8.6.13.

Split Range operation

8.7.

Process controller

8.7.1.

Process controller activation

8.7.2.

Process controller: set modulating behaviour

8.7.3.

Setpoint source (input for process setpoint)

8.7.4.

Behaviour on loss of process setpoint

8.7.5.

Inverse operation

8.7.6.

Internal process setpoint

8.7.7.

Setting procedure

8.7.8.

Proportional gain Kp: set

8.7.9.

Reset time Ti: set

8.7.10.

Rate time Td: set

8.7.11.

Actual value source (input for actual process value)

8.7.12.

Speed source for actual process value

8.8.

Stepping mode

8.8.1.

Stepping mode: activate

8.8.2.

Operation mode for stepping mode

8.8.3.

Start and end of stepping mode

8.8.4.

On times and off times

8.9.

Profibus DP interface

8.9.1.

Bus address (slave address)

8.9.2.

Redundancy

8.9.3.

Response telegrams for AUMA redundancy II

8.9.4.

Connection type – compatibility with process representation

8.10.

Additional inputs for fieldbus

8.11.

Combination of fieldbus-parallel interface

8.12.

Auto change-over I/O (during fieldbus failure)

8.13.

Functions for FO cable connection

8.13.1.

FO cable monitoring: activate/deactivate

8.13.2.

FO cable topology: check setting

Actuator controls

Table of contents

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды