AUMA ACV 01.2 Скачать руководство пользователя страница 78

Страница: 78 / 168

Function active

<Auto change-over I/O (fieldbus failure> function activated.

8.13.

Functions for FO cable connection

Requirements

FO cable module or FO coupler (for explosion-proof actuators) within actuator
controls.

8.13.1.

FO cable monitoring: activate/deactivate

Actuator controls monitor the FO cable signal for communication, connection and
signal strength.

Device configuration M0053

FOC connection M0600

FO cable monitoring M0709

Default value:

On (not final device)

Setting values:

On (not final device)

Monitoring is activated.

On loss of FOC connection, the following is signalled:

Wrn FOC

Off (final device)

Monitoring is deactivated.

This setting is used if the actuator is the last participant within line topology, or for
all actuators within star topology.

8.13.2.

FO cable topology: check setting

Required user level: .

Device configuration M0053

FOC connection M0600

FO cable topology M0637

Default value:

Star/line

Setting values:

Star/line

Star, line topology

Ring

Ring topology

8.13.3.

FO cable baud rate, check setting

Required user level: .

Device configuration M0053

FOC connection M0600

FO cable baud rate M0642

Default value:

Auto

Setting values:

Auto

Automatic baud rate selection

9.6 kbit/s

–

12000 kbit/s

Setting depending on fieldbus systems and FO cable module or FO coupler.

8.14.

By-pass function

Application

The by-pass function is used, e.g. for district heating pipelines. Under high pipeline
pressure, the gate valve of the main valve cannot be used, pressure compensation
via by-pass valve is therefore required.

Requirements

●

<Additional inputs> or additional <Parallel interface>.

Function

Two MOVs – one main valve and one by-pass valve – are linked via enable signals

Bypass Sync In

and

By-pass Sync Out

. Operation commands can only be executed

if one of the two actuators sends the enable signal to the other device. Enable

Actuator controls

Application functions

ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды