AUMA ACV 01.2 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 168

AUMA ACV 01.2 Скачать руководство пользователя страница 2

Read operation instructions first.

●

Observe safety instructions.

Purpose of the document:

This document contains information for the commissioning, operation and maintenance staff. It is intended to
support local device operation and setting modifications.

Reference documents:

●

Operation instructions (Assembly, operation, commissioning) for actuator.

●

Manual (Device integration Fieldbus) actuator controls AC 01.2 Profibus DP

Reference documents can be downloaded from the Internet (www.auma.com) or ordered directly from AUMA
(refer to <Addresses>).

Table of contents

Page

1.

Safety instructions.................................................................................................................

1.1.

Prerequisites for the safe handling of the product

1.2.

Range of application

1.3.

Warnings and notes

1.4.

References and symbols

2.

Short description...................................................................................................................

3.

Operation................................................................................................................................

3.1.

Operating the actuator from local controls

3.2.

Actuator operation from remote

3.3.

Menu navigation via push buttons (for settings and indications)

3.3.1.

Menu layout and navigation

3.4.

User level, password

3.4.1.

Password entry

3.4.2.

Password change

3.4.3.

Timeout for incorrect password entry

3.5.

Language in the display

3.5.1.

Language change

4.

Indications..............................................................................................................................

4.1.

Indications during commissioning

4.2.

Indications in the display

4.2.1.

Feedback signals from actuator and valve

4.2.2.

Status indications according to AUMA classification

4.2.3.

Status indications according to NAMUR recommendation

4.3.

Indication lights of local controls

4.3.1.

Indication lights: change colour

5.

Signals (output signals).........................................................................................................

5.1.

Signals via fieldbus

5.2.

Status signals via output contacts (digital outputs)

5.2.1.

Assignment of outputs

5.2.2.

Coding the outputs

5.3.

Configurable status signals

5.4.

Analogue signals (analogue outputs)

5.4.1.

Assignment of analogue output 1

2

Actuator controls

Table of contents

ACV 01.2/ACVExC 01.2 Profibus DP

«
1
2
3
4
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов