AUMA ACV 01.2 Скачать руководство пользователя страница 15

Страница: 15 / 168

Functions

Navigation sup-
port on display

Push buttons

Confirm selection

[3]

Save

Enter <Edit> menu

Edit

Display more details

Details

Enter Main menu

Setup

[4] C

Cancel process

Esc

Return to previous display

Backlight

●

The display is illuminated in white during normal operation. It is illuminated in
red in case of a fault.

●

The screen illumination is brighter when operating a push button. If no push
button is operated for 60 seconds, the display will become dim again.

3.3.1.

Menu layout and navigation

Groups

The indications on the display are divided into 3 groups:

Figure 3: Groups

[1]

Start menu

[2]

Status menu

[3]

Main menu

Status menu and main menu are marked with an ID.

Figure 4: Marking with ID

ID starts with

= status menu

ID starts with

= main menu

Group selection

It is possible to select between status menu

and main menu

For this, set selector switch to 0 (OFF), hold down push button C for approx. 2
seconds until a screen containing the ID

M...

appears.

Figure 5: Select menu groups

You return to the status menu if:

●

the push buttons on the local controls have not been operated within 10 minutes

●

or by briefly pressing C

Direct display via ID

When entering the ID within the main menu, screens can be displayed directly (without
clicking through).

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Operation

Содержание ACV 01.2









































































































































































Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды

AUMA ACV 01.2, Руководство пользователя

Результаты поиска

Содержание ACV 01.2

Отзывы:

Похожие инструкции для ACV 01.2

Бренды по названию

Популярные бренды