manualshive.com logo in svg

AUMA ACV 01.2, Руководство пользователя, Страница: 22 / 168

Поделиться
Скачать
AUMA ACV 01.2 Скачать руководство пользователя страница 22

The direction of the operation command is displayed by an arrow above the bar
graph indication. The figure below shows the operation command in direction CLOSE.

Figure 19: Indication for setpoint control (positioner)

E1

Position setpoint

E2

Actual position value

Pivot point axis

The pivot points and their operation behaviour (operation profile) are shown on the
pivot point axis by means of symbols.

The symbols are only displayed if at least one of the following functions is activated:

Operation profile M0294

Timer CLOSE M0156

Timer OPEN M0206

Figure 20: Examples: on the left pivot points (intermediate positions); on the right
stepping mode

Table 3: Symbols along the pivot point axis

Stepping mode

Pivot point (intermediate position)
with operation profile

Symbol

End of stepping mode

Pivot point without reaction

|

Start of stepping mode in direction
CLOSE

Stop during operation in direction
CLOSE

Start of stepping mode in direction
OPEN

Stop during operation in direction
OPEN

–

Stop during operation in directions
OPEN and CLOSE

–

Pause for operation in direction CLOSE

–

Pause for operation in direction OPEN

–

Pause for operation in directions OPEN
and CLOSE

4.2.2.

Status indications according to AUMA classification

These indications are available if the parameter 

Diagnostic classific. M0539

 is set

to 

AUMA

.

Warnings (S0005)

If a warning has occurred, the display shows 

S0005

:

●

the number of warnings occurred

●

a blinking question mark after approx. 3 seconds

Figure 21: Warnings

For further information, please also refer to <Corrective action>.

22

 Actuator controls

Indications

 ACV 01.2/ACVExC 01.2 Profibus DP

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов